First, the main factors of electrical fire
1, electrical circuit short circuit, overload, excessive grounding resistance, etc. Cause a fire.
2. Fire is caused by long-term uninterrupted operation of equipment in the computer room or equipment failure.
3. Fire caused by static electricity.
4, lightning and other strong electricity intrusion caused a fire.
Second, the disposal procedures
1. After finding the fire, cut off the power supply quickly, put out the fire with the nearest fire extinguisher, report according to the special accident notification mechanism, and report the specific situation of the fire to the leader.
2, quickly organize relevant personnel to carry fire fighting equipment to the scene, and obey the command of the site commander.
3. If the fire is serious, you should immediately get in touch with the building fire control center and negotiate treatment measures with it. If professional fire fighting is necessary, please call the leader at once and call 1 19.
Third, matters needing attention
1. When there is a fire in the computer room, the following principles should be followed: First, ensure the safety of personnel; Secondly, ensure the safety of key equipment; Then ensure the safety of general equipment; In the process of putting out the fire, you should put out the fire and call the police.
When a fire breaks out, the first discoverer will find out the cause of the fire. If it is caused by power supply, first cut off the power supply.
Fourth, preventive measures.
1, check the electrical equipment in the machine room regularly. Equipment with problems should be repaired in time to eliminate potential safety hazards.
2. Regularly monitor the temperature of important electrical equipment and electronic equipment in the computer room every day, which can find and eliminate hidden dangers in time.
3, should organize relevant personnel to carry out fire safety education, learn fire knowledge, learn to use all kinds of fire extinguishers correctly, and carry out relevant fire drills in a planned way.
Emergency plan for electrical fire 2 Article 1 Open fire and smoking are prohibited in the computer room. All equipment in the computer room should be maintained regularly, and inspection records should be made, and it should be cleaned according to the actual situation of the computer room.
Article 2 The network administrator is responsible for the maintenance of the network equipment in the computer room. If machine faults are found, they should be eliminated in time. If there is a fault within the scope of hardware three guarantees, you should contact the supplier in time or send the machine to the supplier for maintenance.
Article 3 Hotel employees must strictly abide by the relevant regulations on the operation and management of computer rooms, equipment and systems, and may not engage in work unrelated to system management, operation and maintenance, system installation and debugging in the computer room.
Article 4 do a good job in fire prevention, rain prevention, moisture prevention and theft prevention, and pay attention to the safety of electricity use; Check the temperature, humidity and power supply system of the computer room environment every week to see if it meets the relevant standards of the computer room.
Article 5 Switches and servers in the computer room are key equipment for hotel operation, and no one may configure or change their system parameters by himself.
Sixth, we should do a good job in the security of the computer room, and keep all kinds of accounts and passwords of the server strictly confidential.
Article 7 Data backup shall be made in time to ensure that data can be recovered quickly and safely when the system fails. All backup data shall not be changed, and local and off-site backup and storage are required.
Article 8 In order to ensure the normal operation of the hotel network, the equipment in the computer room should be inspected every day, mainly focusing on whether the servers and network equipment are in normal operation.
1. Adjust the temperature of the computer room. If the indoor temperature is too high, adjust the air conditioner to effectively ventilate the computer room.
2. Check the working status of switches, firewalls and access devices, and timely and effectively maintain any abnormality.
3. Monitor network operation.
Article 9 Except the hotel network administrator, other personnel of the company need to be accompanied by the network administrator when they enter the computer room for work.
Article 10 It is strictly forbidden for personnel from out-of-band units or irrelevant personnel to enter the computer room. If it is really necessary for work, such as system fault diagnosis and treatment, equipment maintenance, system or equipment installation, etc., they must be accompanied by network administrators to cooperate with the implementation of the project.
Eleventh equipment entering the computer room should be removed before entering the computer room to ensure the cleanliness and safety of the computer room environment.
Article 12 It is forbidden to bring inflammable, explosive and corrosive dangerous goods into the computer room.
Article 13 UPS power supply provided by the computer room is only allowed to supply power to core equipment such as host computer, server, network and storage. It is forbidden to insert other equipment to increase the power supply load of UPS power supply.
Article 14 It is forbidden to cut off the power supply of the system without authorization. If it is really necessary to cut off the power supply due to work, the corresponding preparations should be made first, approved by the department leaders, and then the power failure or power failure should be notified to all departments before implementation.
Article 15 When installing electrical equipment or items that need electricity in the computer room, professionals or installation engineers of equipment suppliers must conduct on-site investigation and confirm that they meet or meet the requirements before implementing the project.
Emergency Plan for Electrical Fire 3 I. List of Leading Groups for Safety Production
Team leader:
Members:
Second, the emergency rescue organization
Safety production headquarters
1, commander in chief:? Fully organize and mobilize personnel.
2. Deputy Commander-in-Chief: Coordinate the work of the commander-in-chief, command personnel to extinguish fire and evacuate personnel and materials, and perform the duties of the commander-in-chief in his absence.
3. Leader of fire fighting action group: number: 20.
4. Head of Communication Liaison Group: Number: 2
5. Leader of the evacuation guidance group: number: 3
6. Captain of safety protection and rescue team: number: 3
Third, the initial fire extinguishing procedures and measures
1. In case of fire, cut off the power supply and fire source in time, and use fire extinguishers and indoor and outdoor fire hydrants nearby to put out the fire.
2. Remove inflammable and explosive chemicals in the fire area and rescue the wounded and valuables.
3, when the fire area is larger, the situation is more serious, to evacuate the scene in time. 4, when the fire brigade arrived at the fire to cooperate with the fire brigade to put out the fire.
Four, alarm and alarm handling procedures
1. Anyone who finds a fire must immediately notify the people around him and report the fire: you can call the fire brigade by shouting "Fire" or calling "1 19".
2, fire personnel on duty after receiving the fire signal, should be confirmed immediately. After confirming the fire, immediately notify the personnel of the unit to rush to the scene and report to the safety production headquarters. According to the deployment of safety production headquarters, notify relevant personnel to take action. When dialing "1 19", you should say: Qiao Ben Electric Appliance Factory at Zugezhuang Dongkou, and explain the alarm telephone number and name. After the alarm, send someone to the intersection at the door to welcome the fire brigade into the fire.
Verb (abbreviation of verb) organizational procedures and measures for emergency evacuation
1. Open all safety evacuation doors, clean up the debris in the evacuation exits and passages, ensure the safety and smoothness of the evacuation exits, and organize the personnel present to evacuate from nearby safety exits.
2. Stabilize the mood of fire survivors and guide them to use the correct escape method. Guide everyone to evacuate safely and prevent crushing injury and trampling injury.
3. Evacuate the vehicles in the fire scene in time and pay attention to traffic diversion.
Six, fire emergency rescue plan
1. In order to effectively and quickly put out the fire, evacuate people and reduce fire hazards as much as possible, this plan is formulated according to the Fire Safety Management System for Public Entertainment Places and other laws and regulations.
2. In case of fire, conduct initial fire fighting, alarm, evacuation and comprehensive safety protection according to the operation procedures of the plan.
3. If smoke is found in the market or a fire report is received, the commander-in-chief and deputy commander-in-chief will lead the fire fighting action group to carry out emergency fighting, and dry powder fire extinguishers will be used to extinguish the fire at the early stage of the fire or when the fire is small. If it is determined that the dry powder fire extinguisher cannot be used to extinguish the fire, start the fire hydrant immediately according to the instruction and call the police immediately. (Alarm number: 1 19)
4. In the event of a fire accident, the evacuation team leader will lead the members of the evacuation team to evacuate the vehicles and personnel at the scene from 8: 00 am to 5: 30 pm during the day, clear the way for the fire truck in time, and guide the fire truck into the fire scene. In different places, the team leader maneuvers to master the command.
5. During the fire fighting, if there are casualties, the team leader and members of the safety protection and rescue team are responsible for reporting to 120 for first aid from 8: 00 during the day to 5: 30 in the afternoon, and taking the injured away from the fire scene quickly.
6. When there is a fire accident at night, the security team should carry out emergency rescue, and immediately notify all the teams and personnel present to arrive at the fire scene, and carry out rescue according to the operating procedures of this plan and the division of labor of emergency rescue organizations.
Seven, safety protection procedures and measures
1, draw a warning line and determine the boundary range. Strictly protect the scene, prevent irrelevant personnel from entering the fire, and prevent bad guys from taking the opportunity to destroy and steal.
2, to assist medical staff to rescue the wounded in the fire.
3. After the fire is put out, protect the site and wait for the arrival of fire investigators. Find out the cause of the fire as soon as possible.
Emergency plan for electrical fire. Prevention, Judgment and Treatment of Electric Shock Accidents
1, prevention and judgment
1) Electrical equipment maintenance must be carried out by more than two people;
2) Electrical equipment that needs maintenance should be powered off first. Hang warning signs to judge that there is no electricity, and then hang grounding wires before construction;
3) Electrical equipment for live operation and maintenance shall be well insulated;
4) The above work must be carried out in strict accordance with the electrical operation procedures.
Step 2 deal with
When an electric shock accident occurs, cut off the electric shock power supply first. If the power supply cannot be cut off nearby, use an insulating rod or a dry, non-conductive rod or wood to separate the electric shock victim from the power supply or equipment. And take emergency rescue measures for those who get an electric shock.
Second, the prevention, judgment and treatment of electrical equipment fire accidents
1, prevention and judgment
Check electrical equipment regularly. Whether the motor, switch, circuit and electrical equipment are overheated during operation. Whether the connector is loose or other abnormal phenomena occur. Repair abnormal equipment in time.
Step 2 deal with
In case of fire, first cut off the power supply of fire-fighting equipment or lines. (If possible, it is best to cut off the power supply of adjacent equipment). Then use a dry powder fire extinguisher to extinguish the fire at the scene of the fire. And pay attention to the adjacent parts have electricity. Be safe. It is forbidden to put out fires with water.
Three, emergency trip accident prevention, judgment and treatment
1, prevention and judgment
1) Electrical equipment not put into use shall be inspected regularly and put into trial operation. It is necessary not only to ensure the good standby state of the equipment, but also to evaporate the moisture of the electrical equipment itself, protect the insulation and prevent corrosion.
2) For the running equipment, turn the car before running and run it according to its rated power.
3) Operating equipment shall regularly check its working current, which shall not exceed its rated current value.
4) Before the electrical equipment lines are put into use, check the insulation to ensure that the insulation meets the requirements.
5) The electric switch shall be set with heat load regularly.
Step 2 deal with
Power transmission should not be resumed immediately after electrical equipment trips. Find out the reason, and then switch on according to the power failure steps.
Emergency plan for electrical appliances fire 5 When a fire accident occurs in the information room, this plan is formulated in order to enable the personnel on duty to handle the incident calmly and orderly. Please study hard, be familiar with the emergency procedures, improve the emergency ability of all employees, and do your best to ensure the personal safety of employees and reduce losses in an emergency.
The cause of the fire is generally that the open flame management is not in place; Improper management and use of electrical equipment; Arson and other reasons.
Option 1: When you smell burning,
When the personnel on duty find the smell of smoke or burning in the information room, it may be smoldering somewhere or the power supply is overloaded, which may easily cause a fire. The personnel on duty should immediately find out the cause and place, and take measures such as quickly extinguishing the fire source or turning off the main switch of power supply, isolating flammable materials near the fire source, closing the window and so on according to different situations to eliminate fire hazards and prevent fires. Immediately report to the security department afterwards, and do a good job in site protection to prevent the fire from rekindling. Don't leave the scene or hide the accident at will.
Scheme 2: Fire or smoke is found while on duty.
Because the fire source is hidden or other unexpected reasons, the hidden dangers of fire are not found and eliminated in time, resulting in open flames and smoke, and the burning area is not large, which is the initial stage of fire. When the personnel on duty find fire or smoke, they should avoid panic, be calm and decisive, and cooperate with other personnel on duty to quickly find out the reasons and organize fire fighting. When the fire is out of control, the disposal methods are as follows:
First, designate a special person to call "1 19" fire alarm immediately and report to the superior security department, and report to the department and the surrounding people and the masses;
Second, organize the personnel present in the unit and department to put into the fighting work in an orderly manner, and make full use of fire hydrants, fire extinguishers, buckets and other equipment to put out the fire. We should not wait passively for the arrival of the fire brigade and miss the opportunity to put out the fire. We should try our best to put out or control the spread of the fire, and we should not just flee from the fire for personal safety.
The third is to shout loudly for the support of surrounding units and the masses;
Fourth, while organizing fire fighting, we should immediately organize personnel to evacuate and transfer articles, especially inflammable and explosive articles, cash and important documents vulnerable to flame, to a safe place in time, and send people to guard them to ensure safety;
Fifth, attention should be paid to protecting the scene and maintaining good order after fire fighting, so as to facilitate the fire department to investigate and analyze the cause of the fire.
Precautions:
When giving an alarm, the alarm personnel should explain clearly to the fire department the location, unit, type and size of the fire, and greet and guide the arrival of fire-fighting vehicles at the street or intersection after giving an alarm; Upon arrival, firefighters should immediately explain to the fire commander what materials and valuables are stored in the fire, whether there are explosives and toxic substances in the fire, and assist the fire department in maintaining order at the scene. Pay attention to the fire site and environment when extinguishing the fire by yourself, so as to prevent being trapped by fire, smoke poisoning, falling objects, etc. Put out the fire while ensuring your own safety.
Emergency plan for electrical fire Article 1 Emergency incidents in computer rooms include network equipment or server failures and physical damage (water, fire, electricity, etc.) caused by natural disasters. ), safety accidents caused by human error, etc. Preventive measures for emergencies include: establishing a safe, reliable and stable operating room environment, fire prevention, theft prevention, lightning protection, waterproof, antistatic and dustproof; Establish a standby power supply system; Strengthen the awareness of fire prevention and theft prevention.
Article 2 The emergency plan for water leakage in the computer room is as follows:
First, when the computer room leaks, the first witness shall immediately notify the computer room management personnel.
2. If there is water leakage in the air conditioning system, the computer room administrator should immediately arrange to stop using the faulty air conditioner, remove the accumulated water in the computer room, and contact the equipment supplier in time for treatment. If necessary, you can temporarily cool the server with an electric fan.
Three, if the wall or window leaks, the computer room management personnel should immediately take effective measures to ensure the safety of the computer room, and at the same time arrange to inform the engineering personnel to clean up the accumulated water in time, repair the wall or window, and eliminate the hidden danger of water leakage.
Article 3 The emergency plan for computer room fire is as follows:
First, improve the environment of the computer room and ensure that fire extinguishers are placed in the computer room; It is forbidden to bring inflammable and explosive articles into the computer room.
Second, the computer room management personnel should be familiar with the internal fire safety operation and rules of the computer room, understand the working principle of fire fighting equipment, master the steps, measures and essentials of fire emergency treatment, and know how to put out the fire, which will put out the initial fire source.
Third, in the event of a fire, quickly cut off the power supply of the computer room to avoid the spread of the disaster, and contact the security department immediately to report the fire when necessary.
Article 4 The emergency plan for power failure in the computer room is as follows:
1. After receiving the power outage notice, relevant information should be released through the office system and telephone in time, and specific measures should be deployed to stop business and save data before the power outage.
Second, the computer room administrator should check the status of UPS power supply every day to ensure that the UPS power supply can automatically power the server to work normally for more than 15 minutes in case of sudden power failure, and ensure that the data of employees' work is saved in time.
Article 5 The emergency plan for communication network failure is as follows:
A, communication line interruption, abnormal traffic and other failures, found that the situation of employees or department leaders should promptly notify the network administrator.
Second, after the network administrator knows the situation, he will quickly organize to detect the fault area and make relevant fault treatment, gradually restore the network connection between the fault area and the server, and restore the communication network to ensure normal operation.
Article 6 The emergency plan for server failure is as follows:
A, computer room management personnel check the status of each server in the computer room every day.
Second, back up the data of the data server regularly. And copy the backup data to the mobile device. When the server has serious hardware failure, the standby server is enabled to ensure normal operation.
Emergency plan for electrical fire 7 This plan is formulated in order to conscientiously implement the regulations of the State Council on the investigation of administrative responsibility for extraordinarily serious safety accidents, actively improve the emergency handling ability of major safety accidents in key parts of our company, strive to reduce losses caused by various extraordinarily serious safety accidents, eliminate hidden dangers of fire accidents, and ensure the safety of company property and employees.
This plan is formulated for the fire in the communication room of our company.
The fire extinguishing process of the mobile communication room is as follows:
(a) the personnel on duty found a fire in the computer room (including the monitoring center personnel) should immediately go to the scene to check.
(2) When individual circuit boards catch fire, pull out the burning circuit boards and put out the fire with 12 1 1 or carbon dioxide fire extinguisher.
(3) When several circuit boards and cables of a cabinet catch fire, immediately pull out the burning circuit board and spray the extinguishing agent with 12 1 1 or carbon dioxide fire extinguisher.
(4) When the cabinet of the computer room is on fire and the personnel on duty are unable to put out the fire and save themselves, the monitoring center should cut off the power supply of the cabinet or floor, turn off the air conditioner, prohibit opening the window, and report to the leading group of the company's safety production management in time.
(5) The leading group of the company's safety production management directs the members of the obligatory fire brigade to put out the fire, organizes the personnel on duty to leave the scene immediately, closes the doors and windows, presses the regional automatic fire extinguishing button to put out the fire, calls 1 19 for help, and reports to the company's competent leader or the safety duty room and monitoring room at the same time, and broadcasts a fire alarm.
(six) after the arrival of the fire brigade, it should actively cooperate and briefly explain the fire location, fire situation and remedial measures that have been taken.
(7) If you can use 12 1 1 to spray fire extinguishing agent or carbon dioxide fire extinguisher, you should cooperate with the fire brigade to protect the site, eliminate hidden dangers and prevent the fire from happening again.
(8) If it is impossible to put out the fire with 12 1 1 or carbon dioxide fire extinguisher, in order to prevent smoking poisoning, people should be evacuated in an orderly manner, and corresponding fire extinguishing equipment should be used as soon as possible.
(nine) should protect the scene, according to the accident investigation and handling measures.
(10) Fire alarm telephone number: 1 19.
Special matters that should be paid attention to in this plan
1. In case of fire, while dealing with and ensuring personal safety, take corresponding rescue measures according to the importance of the equipment, ensure the important equipment, especially the direct telephone, upload corresponding data with northern Hebei and northern China, and ensure the smooth passage.
2. After the rescue of major equipment, after the repair of minor equipment and accident treatment, the corresponding experiments are carried out to ensure the operability of the equipment, and the feasibility of the equipment is analyzed.